This standard is issued under the fixed designation D ; the number immediately following fication System D lists the ASTM materials standards that. ASTM D , defines a punch-type of shear test. This test method covers the procedure for determining the shear strength of composite materials in the form of . Description: Description: tn_THSASTM-D THS Shear punch fixture. to test shear strength of plastics by punch tool according to ASTM-D
|Published (Last):||17 September 2011|
|PDF File Size:||3.10 Mb|
|ePub File Size:||13.45 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D specifies constant rate of extension testing machine universal test machine.
ASTM D Shear Punch Test Equipment for Plastics
However, it must be recognized that ast, end-use applications there are likely to be many factors not taken into account in this test method, such as stress-concentrating geometries and rates of shear, which can profoundly affect the measured shear strength. The lower end of the punch is then placed in the hole in the base plate lower left and the cover plate top is bolted on to hold the specimen securely in place.
Enabling you to astk and mitigate the intrinsic risk in your operations, supply chains and business processes. ASTM D covers punch-type shear tests used in determining the shear strength of test specimens of organic plastic sheets and molded disks in thicknesses from 1. Figure 2 shows two such fixtures. Moreover, the fact that the shear strength is calculated by dividing the load by the area of the shear strength is calculated by dividing the load by the area of the sheared edge circumference X thickness should not be interpreted as indicating that the shear strength value so obtained is solely a material property, independent of thickness.
A male punch is then forced satm the hole in the metal fixture causing shear along the edge of the hole. Assurance Testing Inspection Certification. However, a uniform shear stress state is not attained; severe stress concentrations occur at the edges of the punch. Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. The shear force is simply calculated as the maximum force applied divided by the shear area punch circumference x specimen thickness.
Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
ASTM D732 TESTING FIXTURE
This test method is intended as a comparative test, and not as a quantitative measure of the shear strength of the material. Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.
Forces up to 10 kN 2, lbf Low force tabletop systems Modular series of five frame options with adjustable test space Affordable testing option for tension, compression, bend, peel and much more. Shear strength results are important to designers of film and sheet products that tend to be subjected to shear loads, or in applications where applied crushing loads are a risk. Touchstone Research Laboratory, Ltd.
The results are expressed as shear strength and are given in the units of MPa or psi. This specimen is clamped between the two hardened steel disks of the punch shown at the lower right of the photograph. Due to the very large number of tests offered, descriptions of those d372 commonly requested have been gathered into the following groups: A universal testing machine is used to push the punch until shearing of the specimen occurs.
Send us a request Wilton UK: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
We are confident that we have what you are looking for. Sources of Additional Information: Moreover, the fact that the shear strength is calculated by dividing the load by the area of astn sheared edge punch circumference X specimen thickness does not interpret as indicating the shear strength value so obtained is solely a material property, independent of thickness.
Shear strength obtained by a tool of the punch type is one of the recognized methods of comparing materials or obtaining data for engineering design. By means of our plastic testing expertise and modular product design, we will help find the testing solution that is right for you.
The test is performed by clamping a test sample attached to a 1-inch punch between two metal fixtures. For both fixtures, a specimen in the form of a bar of rectangular cross section is simply placed in a slot in the base and a flat-bottomed guillotine is pressed against the bar, shearing it into three pieces.
ASTM D test procedure: Alternate Punch Shear Fixture Configurations. Inspection Validating the specifications, ast and safety of your raw materials, products and assets.
Certification Formally confirming that your products and services meet all trusted external and internal standards.
Historical Version s – view astj versions of standard. The area of the sheared edge is equal to the circumference of the punch multiplied by the thickness of the specimen.
Select from list below: Specimen thicknesses can range from 0. It is intended for use as a atm screening and materials comparison test of plastics available in the form of sheets or molded disks. Related Polymer Shear Test Services: The values given in parentheses are for information only. Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world.
Auditing Consulting Sourcing Training. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.
ASTM D – 17 Standard Test Method for Shear Strength of Plastics by Punch Tool
Have a question about conducting the test for this standard? Shear strength obtained by a tool of the punch type is one of the recognized methods of comparing materials or obtaining data for engineering design.
The specimens are usually 2 inich diameter discs or 2 inch squared plates and thickness ranging between 0. Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. ASTM D testing covers the punch-type shear test and is intended for use in determining the shear strength of test specimens of organic plastics in the form of sheets and molded disks in thicknesses from 0.