ASTM E1300 PDF

New Provisions in ASTM e‐ A comparison of the Basic and New Analytical Procedures for Determining the. Load Resistance of. ASTM E Standard Practice for Determining Load Resistance of Glass in Buildings Book of Standards Volume American Society for. ASTM E is the main source of technical information for architects and other design professionals to determine the right glass thickness and type to meet a.

Author: Taukasa Fegul
Country: Yemen
Language: English (Spanish)
Genre: Video
Published (Last): 8 January 2007
Pages: 385
PDF File Size: 6.13 Mb
ePub File Size: 7.72 Mb
ISBN: 225-4-69047-291-7
Downloads: 83603
Price: Free* [*Free Regsitration Required]
Uploader: Doutaxe

Work Item s – proposed revisions of this standard.

Designing Glass to Resist Wind and Snow Loads

The single source for information on designing, specifying and building with commercial glass. The surface condition of the glass doesn’t have any significant damage. IGUs reduce the likelihood of interior condensation forming by providing a thermal barrier between the inside and the outside.

Determination and Report of Procedures.

ASTM E – 00 Standard Practice for Determining Load Resistance of Glass in Buildings

Appendix X1 provides additional procedures to determine maximum lateral deflection for glass simply supported on four sides. Glass 6mm thick will weigh 2. Determination ast Report of Procedures.

Typically all four sides are supported in a framed window or a four-sided Structural Silicone Glazing. The thermal barrier makes interior spaces more comfortable as it is easier to maintain astmm consistent indoor environment.

The load share factor, which is the multiplying factor derived from the load sharing between two lites of equal or different types or thicknesses.

Monolithic, laminated and insulating glass constructions made with annealed or heat-treated glass. D Practice for Plastics: About The Education Center.

  CNY74 DATASHEET PDF

Work Item s – proposed revisions of this standard. For conversion of quantities in various systems of measurements to SI units refer to Practice E The final thickness and type of glass selected also depends upon a variety of other factors see 5.

This practice does not address aesthetic issues caused by glass deflection. The procedures operate under some basic assumptions related to glass fabrication and installation, including:. Determination and Report of Procedures.

However, some applications can be two-sided support, such as Butt Joint Glazing or sometimes even three-sided or one-sided supports. Link to Active This link will always route to the current Active version of the standard. For insulating glass units, this practice only applies to insulating glass units with four-sided edge support.

The values given in parentheses are for information only. There is a multi-step process that must be undertaken to help ensure the glass in your project is able to resist these loads. Glass Education Center The single source for information on designing, specifying and building with commercial glass. D Practice for Plastics: Active view current version of standard. The design load needs to be in psf or kPa. These factors include but are not limited to: Specifying Large Insulated Glass Units.

Accommodating for wind and snow is one of the important upfront considerations in the design and specification process. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Astm e 1300

Tempered glass is four times stronger than regular glass; heat strengthened is ast, two times aztm. Referenced Documents purchase separately Qstm documents listed below are referenced within the subject standard but are not provided as part of the standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  ASCITIS EN AVES PDF

A procedure is also presented to calculate the probability of breakage of any annealed lite or ply see Appendix X3for short or long duration loads. In addition, considerations set forth in building codes along with criteria presented in safety-glazing standards and site-specific concerns may control the ultimate glass type and thickness selection.

Link to Active This link will always route to the current Active version of the standard.

The procedures operate under some basic assumptions related to glass fabrication and installation, including: Link to Active This link will always route to e130 current Active version of the standard.

Active view current version of standard. The word window comes from a Norse term translated “wind eye”, for “eye on the weather.

Resist Wind & Snow Loads | Vitro Glass Education Center

Basic Design Procedures The assumptions and calculations result in these basic design procedures asstm should be followed: This practice does not apply to glass with surface or edge treatments that reduce the glass strength. Work Item s – proposed revisions of this standard. This practice is not applicable to any form of wired, patterned, etched, sandblasted, or types of glass with surface treatments that reduce the glass strength.

The resulting load resistance, which is the uniform load that a glass construction can sustain without breaking.