This manual describes the control of the standard series. COMBIVERT F4-Small. It includes: General installation and connection instructions. Explanation of the. Prima leggere le manuale di istruzione 1 parte! Leer manual de instrucciones parte 1 antes! BETRIEBSANLEITUNG KEB COMBIVERT F4-S. Manuals and User Guides for KEB COMBIVERT F4-F. We have 3 KEB COMBIVERT F4-F manuals available for free PDF download: Applications Manual.
|Genre:||Health and Food|
|Published (Last):||22 March 2015|
|PDF File Size:||5.62 Mb|
|ePub File Size:||11.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
B 80 60 60 12 16 53 The approximate braking time can be determined according to following formulae. Combicert strip binary-coded Name: This data is only valid for units with internal brake transistor see “unit identification”.
If the value is not achieved, please contact KEB. High Operating Temperatures Display And Keyboard Functional Description Sychronous Control Name: Checklist Prior To Start-up The parameters for the precontrol profile Pd. Encoder Interface Channel When displayed in increments Pc. If the desired braking time is smaller than the calculated braking time, it will be necessary to use a braking resistor. In the fixed parameter groups the parameters are combined function-related.
KEB COMBIVERT F4-F Applications Manual
Gain Of Output Characteristic Temperature Control The control is activated via the transistor output do. A 62 41 07 3 8 21 Dependent on the available space and filter type the filter can either be installed under the frequency inverter submountedor beside the frequency inverter mnaual mounted.
Sustained oscillation with high amplitude Solution: On exceeding the level adjusted with CP. Table of Contents Add to my manuals Add. This measure does not protect with a defect of the braking transistor however against the developing extreme overload with acute danger of fire.
Motor Name Plate Page 48 In the field weakening range larger tolerances are possible, also see reference on page 4 M [Nm] CP. Drive Curve Door Drive Don’t have an account? Additionally the noise immunity of the system is improved and the DC-link capacitors lifetime increases.
Output 4f Stabilization Typical values are for normal operation: The standard-sinus filters are made for an output frequency of max.
It’s a community-based project which helps to repair anything. The setpoint is defined only by the setpoint signal at REF1.
KEB COMBIVERT F4-F Manuals
It shall allow a correct entering into this field. B 95 55 13 20 54 External Error Control Procedure A.
B 81 18 3 75 To utilize the maximum possible braking torque the frequency inverter must be layed out for the increased current. Aux-function, Setpoint And Rotation Selection Questo comprende, specialmente, la conoscenza e le osservanze delle direttive di sicurezza e di avvertimento sootonindicate.
The operation of other electrical loads is forbidden and can lead to disturbances of the unit. Check whether the desired d4 time is attained with the braking resistor tBmin.
KEB COMBIVERT F4-F APPLICATIONS MANUAL Pdf Download.
Logic Operation Of Switching However, if you have cause for complaint the unit should be returned stating invoice number, delivery date, cause of failure and field conditions. To print the manual completely, please, download it. Todos los derechos reservados. For further filters e.
Keb COMBIVERT F4-F Manuals
Used Parameters 5,00 s 0,01 s Setpoint Calculation At SP. To set the setpoint value by way of the motor potentiometer parameter SP. AA 11 read graph 2 B —— 6. Project Planning see Technical Data air flow rate of fan For more details please refer to the catalogs of the control cabinet manufacturers. This is especially true for the attention, safety and warning guides.
The proportional factor of the position controller is adjusted in CS. Page 79 —— 6. Selection Of Switching Conditions do.