Arming the System. Check the following items before arming the system: Bypass Light. If the “Bypass” light is ON, insure that zones are intentionally bypassed. User Manuals · Request a Service · Request a Quote · Security Tips. Call us now on DSC – PC User Manual · DSC – PC User Manual. View and Download DSC PC installation manual online. DSC PC Installation Manual. PC Security System pdf manual download.
|Published (Last):||13 January 2015|
|PDF File Size:||5.92 Mb|
|ePub File Size:||9.3 Mb|
|Price:||Free* [*Free Regsitration Required]|
Use zone bypassing when access is needed to part of the protected area. Should your system fail to operate properly, call your installer for service. An entry through any zone programmed as a delay zone will create an instant alarm. I vsc expect to find a web forum with help on this topic Im a new homw owner with a DSC as well. I just want to set my alarm to chime when the doors open. Detailed mznual for the default procedure are listed in the manual. If the smoke detector is reset but goes into alarm again after the second delay, the fire alarm will sound again and the process described above will repeat.
The PC can be programmed at the time of installation to automatically perform a test transmission to the monitoring station on a regular basis. If the system has not been programmed for this automatic lest, call the monitoring station for instructions on how to perform a test mqnual. Order from this website and it will be delivered to your door, fight traffic and look for a Batteries-Plus. Could someone manuxl me as to where I can find the pv1550 manual for PC Also, damaged wiring or contacts on a zone may be temporarily bypassed until repairs can be made so that the panel can be armed.
As each digit is entered, the keypad sounder will beep. I sent you a Private message with instructions for downloading a manual free of charge, courtesy of the folks at The Home Security Store. Do not unintentionally bypass zones when arming. The zone lights are used to indicate the program status of the 6 security codes light off-code is not programmed ; light on – code is programmed ; light flashing – this code mahual being programmed.
DSC PC INSTALLATION MANUAL Pdf Download.
I ;c1550 try replacing the battery. Logged shadoweasel Member Posts: February 03, If I reset the password I will erae all the previous configuration zones etc? I’ve been looking for the installation manual for this system as well, care to help me out Old EW tech?
Notification to Telephone Company Upon request, the customer shall notify the telephone company of the particular line to which the connection will dcs made, and provide the FCC registration number and the ringer equivalence of the protective circuit.
Logged HenryM Member Posts: Old EW tech on October 11, I would really appreciate that same link to download the installers manual. Remember, mnual [A] key does not ring the bell and the [P] key may not be programmed for an audible signal. I moved into a new mxnual and did not get the Master Codes for the alarm system. November 08, The instructions for defaulting are short and sweet.
There is normally no reason for anyone but the installer to have access to the control panel.
Use the forums search feature and you will find many threads on the topic. The second delay is intended mnual allow you to reset the smoke detectors after a false alarm. If an alarm occurred while the panel was armed, the “Memory” light and the light for the zone which caused the alarm will start to flash and will continue flashing for 2 minutes.
Trouble light ON means there is a fault on the system.
DSC PC Home Security | eBay
Do not nanual the keypad with a wet cloth. Activate each sensor in turn. My alarm just wails until I pull the power and battery. Log in as a member and I will send you a Private Message with downloading information.
Be sure to remove snow from exterior patio doors in winter: Contact your installer for information on safe methods to activate a smoke detector.
Zone Lights, when ON in the normal operating mode, indicate an open zone. I sent you a Private Message with the info. Transmission of the fire alarm to your monitoring station is delayed for 30 seconds to allow you to cancel possible false alarms. Pressing any key on the keypad will silence the beeper but the “Trouble” light will remain on until the trouble condition is cleared.
When testing is complete, call and advise the monitoring station.
If your security system is programmed to report to a monitoring station, the keypad will also sound a tone to indicate that the monitoring station has been advised of the arming of the system. When a Fire Alarm is generated, the bell or siren will sound with a pulsing tone. I would greatly appreciate information on how to get an installation manual so that I can reprogram the alarm!
The control panel will be mounted out of the way in a utility room or basement. The zone light will go OFF as each sensor is restored to normal door or window is closed 5.
When activated, the “Bypass” light will come ON. I recently purchased a villa in the Caribbean!!!! The keypad buzzer will not sound for AC failure until there is also a low battery condition.