HC393 DATASHEET PDF

Rev. 6 — 3 December Product data sheet. Table 1. Ordering information. Type number Package. Temperature range Name. Description. Version. when gated with the Clock of the HC .. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in. HC datasheet, HC circuit, HC data sheet: TI – DUAL 4-BIT BINARY COUNTERS,alldatasheet, datasheet, Datasheet search site for Electronic.

Author: Voodoomi Tokus
Country: Kosovo
Language: English (Spanish)
Genre: Software
Published (Last): 14 October 2014
Pages: 193
PDF File Size: 12.70 Mb
ePub File Size: 7.65 Mb
ISBN: 932-5-62506-980-9
Downloads: 68165
Price: Free* [*Free Regsitration Required]
Uploader: Gokus

The HC devices contain eight flipflops and additional gating to implement two individual 4bit counters in a single package. For the clock I have in mind, setting will proceed as follows. Chip designers have been crafty enough that this has proved satisfactory in most cases. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard e. The device features latch hc933 LE and output enable OE inputs.

This could be the same as the halt signal if halting should also reset the seconds counter. Alternatively, a lot of NE-2’s could be assembled into a neon display. A photograph will be shown here when the film has been developed and scanned. The crystal, which is a small metal cylinder with fine wire leads, will not drive vatasheet Pierce oscillator made with an MPF Designers mustensure compliance with safety-related requirements and standards applicable to their applications.

The clear control consists of two inputs that are AND’ed together. Here, the digit on the right corresponds to the flip-flop on the left in the diagram. The SPDT pushbutton is the hardest thing to find. It is too easy for errors to creep in datasheft various points, and also what you have available dattasheet be slightly different from what the designer used.

  IPC A 610E PDF

It may be fun, but is not hhc393 instructive. The toggle flip-flop, by itself, is a 1-bit counter with the states 0, 1. ENP does not have this property. Note that only one element has to be lighted, and a single dropping resistor used. The LS and LS are modulo decade counters, while the others are modulo binary.

In addition to the normal modulo-N counting from 0 to N – 1, we can also count from N1 to N2, or from N1 to the maximum count. Connect two LS’s in this way, with each set up for normal counting. The 32, Hz crystal is a small cylinder the very small watch crystals are too small to be practical; be sure you get one of the larger ones, about 2. Jun 20, 1.

The outputs go nearly to the supply rails, but can furnish only less than a mA. A shift register is a series of flip-flops with each output Q connected to the next input D, and the clock inputs connected together.

How can I build a simple counter with a HC chip? | Electronics Forums

The electronic wristwatch is a remarkable clock. If you are building a clock, you will need two of these counters, one to count seconds up to minutes, the other to count minutes up to hours. This requires a slow change at the minutes level, as well as a rapid change for large alterations.

Different colors could be used for the upper and lower nibbles. Two toggle flip-flops can be connected so they will count this way, as shown at the left. Controls that operate this way are called asynchronous. The 74HC, a 7-stage ripple counter, can be used to this purpose, as shown in the diagram at the left.

  LA TENCA Y LA NIEVE PDF

This will be the 4 output Q3if the input is to C1 the outputs have been relabelled ch393 the new input.

The circuit is shown at the left. All the circuits should be tested on the breadboard and made to work before the final circuit is assembled. The same trick is used, but since the clearing is synchronous, the counter must be reset to 1, not 0. Not recommended for new designs. Without the capacitors, the crippling sensitivity of CMOS to noise here, bad edges is easily seen, a result of the high-impedance inputs.

Hc393 datasheet pdf

However, the signals must be buffered, and cannot be used directly off the ‘s. A counter is a sequential dayasheet machinesince the outputs depend on past inputs, not simply on the current values of the inputs. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device. It was not possible to pull the oscillator frequency significantly by adding capacitance in parallel with one of dafasheet 22 pF capacitors.

Bad clock edges are the main source of difficulty with counters.