57DP-12-2C2 RELAY PDF

RELAY 57DP 1C6 24V. RELAY 57DP 1C6 6V. RELAY 57DP 1C/O 24V OEN. RELAY 57DP2C2 12V. RELAY 57DP 2C2 16V. RELAY 57DP 2C6 24V. RELAY. Supply Of Oen Relay 57DpV-2C Make- Oen/Pla/Omron. Details As Per Annexure-A. | Due date: 28 Jun, | Tender work Value. 57DPB2 57DPB6 57DPA2 57DPA6 57DPC2 57DPC6 57DPA2 57DPC2 57DPC6 57DPC2 57DPC6 57DPB2 57DPB6 Description, MINIATURE POWER RELAYS.

Author: Mauzilkree Zulkik
Country: Bolivia
Language: English (Spanish)
Genre: Business
Published (Last): 6 January 2017
Pages: 78
PDF File Size: 3.13 Mb
ePub File Size: 5.88 Mb
ISBN: 154-6-61800-891-7
Downloads: 15555
Price: Free* [*Free Regsitration Required]
Uploader: Kekasa

G90 When a positional move is commanded, the axis will move to the programmed destination in the negative direction only. If you realize that you entered an incorrect value after pressing ENTER and proceeding to the next parameter, use the down arrow to return to the previous parameter, press ENTER and correct any errors.

D-7 Connection diagram for DEA For example, to remove an intermediate point in a structured program, use block delete to remove the block data and renumber the following block rather than just editing the intermediate block to the same endpoint as the block following it. This would be required at full depth, for example. Screen 3 and sub-screens are only displayed if a spindle axis has been configured in Process parameter P02 Axis Configuration.

Sign Up to Newsletter

To recover, you must press the CE Clear Error key. The following error is calculated as follows: By erlay is, all positional moves in the user program will be based upon the position of the motor encoder and the next parameter will be displayed.

Auxiliary output is turned on to signal the Line Control that the table is ready to be clamped. SP11 Gain 2 0 – 9. See the next page for an explanation of key number 4. External Rotary Encoder Revs In: B-7 Units Text Subclass If the cam search direction was positive: Programming G69 is programmed similar to any move 57pd-12-2c2. External registers do not have a clear, as any relzy value entered will overwrite the existing value.

Install the DLF board. For those cases where the user wants to enter External Tool Correction values, but does not want to implement the handshaking, external data can also be to sent into the standard Tool Correction registers.

  AN ADVANCED APPROACH TO DATA INTERPRETATION BY R.S.AGARWAL PDF

N-Output Variable or Torque Bit 7: The I-Gain influences a rate of torque generated by the drive when it detects a difference between the commanded speed vs. After the default gains are loaded, they will be displayed and the programmer can still modify the value or press ENTER for each value until the next parameter is displayed.

In incremental positioning G91all movements of the slide are made in the commanded direction to the distance specified, starting from the current position of the slide.

Electric Relays

The maximum value allowed is limited by axis parameter Aa15 Tool Correction. This is done to allow a faster return to the home position after the axis has been referenced, but defaulting to a lower feedrate when seeking home for the first time.

No axes enabled for release 06V48 and later. If the motor operates below this value, it is considered to be at zero velocity. If a high resolution feedback is used, only the values greater than or equal to 0. Whatever the distance the encoder is deflected, e.

57DPC2-Datasheet-PDF中文资料大全-电子产品世界

After you have chosen the appropriate parameter set, the CTA will step you through the available parameters for data entry. All programmed distances and destinations will be in inches. Feed to Positive Stop 2. Therefore, the sign of any position value will be ignored.

These calculations use the speed and acceleration parameters set in the control and the drive. Refer to the description of Host Enabled output on page for a complete list of conditions that must be met to change Host Enabled. Many of the parameters that are entered are used for internal calculations and are also used to set other parameter values during 57ep-12-2c2. These are the same commands used for internal Tool Offsets. Shifts the motor zero point by the value entered here.

The target position of any program move must not be within 2 times the position window configured in parameter Aa17A of the software overtravel limit. Power Threshold The value of the power threshold is set here specified in Watts.

  FAMILIA SALVINIACEAE PDF

There is some mechanical blockage with the external encoder. 57dp-12-2v2 Published by All rights are reserved with respect to the content of this documentation and the availability of the product. Switch the system to Manual mode before proceeding with this procedure.

This screen appears when 3. This will reduce the stress on the system mechanics. This position is relative to the marker pulse on the spindle encoder. Refer to Spindle Parameters on page for a complete description of each parameter used with DIAX01 digital drives. At the drive level, relxy acceleration capability is limited by the amount of peak torque that the drive and motor are rated for.

This will cause the axis to Home in either direction, depending on its position. When a G91 incremental positioning move is made, if the G37 code is active, it will not effect the direction of the rotary motion.

All rights are reserved in the event of the grant of a patent or the registration of a utility model or design DIN Screen 4 Jump Command allows the user to specify the type of jump command to issue at the end of the NC block. Operation can be completely independent of the executive controller.

By doing this, all positional moves in the user program will be based upon the position of the motor encoder and the next parameter will be displayed. In practice, it is very difficult to calculate how all of these timing factors interact. No requirements for proceeding to next block To view any other NC Block, press the ESC key to return to the Programming Mode screen, select Review once again and enter the next block number. For a full explanation of this feature, please see the Homing Section in the Programming chapter.