ALIGN 3GX MANUAL PDF

The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. I have put together the written info on the Align 3GX v I found so far. Mostly for my own memory. I shrunk this info to a Pocket Guide that I will printout (or read.

Author: Malakinos Kigabar
Country: Reunion
Language: English (Spanish)
Genre: Environment
Published (Last): 15 May 2013
Pages: 407
PDF File Size: 3.54 Mb
ePub File Size: 12.74 Mb
ISBN: 226-9-58090-554-9
Downloads: 19485
Price: Free* [*Free Regsitration Required]
Uploader: Doukinos

I have 2 sats, so would I just: This completes the aileron endpoint setup process. This completes the rudder endpoint g3x adjustment for the right side.

Flybarless System – Align

Press the SET button to enter E. There is a direct correlation between servos’ speed to gyro’s performance. Due to the high performance gyro sensors used in the 3GX flybarless system, premium high speed digital rudder servos are mandatory for optimal tail performance.

Wait for some sort of jingle or series of flashing lights then release bind button Does that sound right? Power on Futaba 10C 5. While keeping swashplate level and main pitch at zero degrees, press the SET button to register the neutral point and enter E.

Ailgn to Flybarless System “Direct mode bypassing gyro, for mechanical travel and neutral point setup” to adjust the level of the swashplate and then re-complete the setup.

  BABURIN WINNING PAWN STRUCTURES PDF

Align 3gx pdf manual

Custom parameters have been opened up in 3GX to allow pilots to fine tune numerous settings for swashplate and rudder. Originally Posted by Tulo What software??

Password Please enter a password for your user account. With all channels stationary, move the transmitter aileron stick to the right and then back to center position.

For radio with built 3tx gyro gain settings, gain can be adjusted directly. Check that there is no binding throughout the pitch range 4. This completes the swashplate mixing type recognization process. Setting swashplate acceleration may increase the burst amp draw of servos.

I haven’t been able to find the bind procedure, can anyone help me out?? The allign stick position where main pitch is 0 degree must be maintained. Push the throttle stick on transmitter to the maximum top, and in a few moments LED will go off and system power cycles, indicating the completion of setup process. Should any changes made to the endpoints or subtrims on the transmitter in the future, the 3GX flybarless system initial setup must be performed again.

3bx addition to transmitter, the anti-torque compensation feature can also be set through 3GX interface’s rudder parameter.

Lift up the helicopter by hand, and turn it to the left yaw. Press and hold the SET button while powering up the receiver. Yep, the sats will blink fast whan you power the 3GX, they’ll go out for manuaal few seconds while binding and come back on solid.

  BALESTRINI MICRON PDF

If im not mistaken I believe Futaba does not make satellites for there receivers or one that is compatible with the 3gx. Subsequent setup mode is entered by a single press of the SET button. What software, this software. Pay extra attention to these setup steps. With all channels stationary, move the transmitter elevator stick forward, and then back to center position. If incorr ect movements or servo has no movement, please check servo connection to 3GX as well as radio control system.

Release the button before the flash sequence complete, the DIR green LED will light up indicating the 3GX has been bypassed for mechanical neutral and travel range setup.

The software is the manual. In addition, the 3GX can support all of the CCPM swashplate system currently on the market including 90, and degrees swashplates.

The manual is embedded in the build instructions for the various Align kits. My HK 3GX setup. Proper frame rate must be selected based on your servo’s specifications. This excellent control feel will allow pilot of all skill levels to experience the perfect integration between 3GX and helicopter. The good news is if its a Futaba S-bus receiver then it is capable of using s-bus and one wire to control the lot.