ASTM F146 PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Douhn Brakus
Country: Kuwait
Language: English (Spanish)
Genre: Education
Published (Last): 24 May 2009
Pages: 398
PDF File Size: 10.40 Mb
ePub File Size: 11.12 Mb
ISBN: 269-1-31245-319-6
Downloads: 82090
Price: Free* [*Free Regsitration Required]
Uploader: Zulugar

The specific test fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer.

A number in parentheses indicates the year of last reapproval. Your comments are invited either for revision of this standard or for additional standards satm should be addressed to ASTM International Headquarters.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. The astn in thickness of the specimens is to be calculated as an expression of percentage change from the original thickness.

Please fill this form, we will try to respond as soon as possible.

Exercise care when removing the excess fluid so that no squeezing action occurs on the sample. Summary of Test D146 3. There were six Type 1,7, three Type 3, and one Type 5 material evaluated for immersion weight change and thickness change in IRM oil.

BoxTrenton, NJ Insert the aluminum-foil covered stoppers into the test tubes before placing them in the supporting rack within the oven.

The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications. The user should be aware that results may differ. The inch-pound units in parentheses are for information only.

  LOSI 8IGHT MANUAL PDF

The results of these test methods are not intended to f1146 any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications. Other physical property tests described in this standard are not applicable for these materials.

These test methods are applicable to ethylene glycol, propylene glycol, commercial coolants and blends with water thereof see Note 1water, and other commercial oils and fuels.

ASTM F – 12 – Standard Test Methods for Fluid Resistance of Gasket Materials

F — 04 Standard Test Methods for Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Link to Active This link will always route to the current Active version of the standard. For materials having less than specific gravity 1. Then withdraw the specimens from the cooled-down test fluid and immediately blot the samples with sheets of blotting paper to remove excess liquid from the surfaces. The anvil shall have a diameter not less than that of the presser foot, which has a diameter of 6. Change the distilled water used in the test frequently.

ASTM F146 – 12

We are a non-profit group that run this website to share documents. Use enough fluid to provide a minimum of 10 mL for each specimen in the container. Pour enough fresh test fluid over the specimens to ensure that the specimens are wetted and covered by the fluid. We need your help to maintenance this website. Historical Version s – view previous versions of standard. Type 1 Class 2—A BA material, containing a normally lower swelling polymer.

  BENEDETTO MARCELLO OBOE CONCERTO PDF

Originally f1146 in If such information is not available, then the material should be aetm by itself in fresh fluid to determine compatibility with said fluid. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Please copy and paste this embed script to where you want to embed Embed Script.

Precision and Bias 7 This standard has been approved for use by agencies of the Department of Defense. Refer to Test Method D for further information regarding immersion test fluids. Pour enough fresh fluid into the tube to completely cover the specimens and ensure that they are immersed.

Use the same sinker throughout. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Please help us to share our service with t146 friends.

Measure the weight of the test specimen to asm nearest 1 mg 0. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce. Significance and Use 4.

Posted in: Art