Did your Briggs-Stratton model engine break down? SAVE money and repair it yourself! We are here to help – over genuine Briggs- Stratton. Get Parts and Repair Help for E1 Briggs and Stratton Engine – Engine. View parts like Plug-Spark and Grommet. Find great deals for Briggs & Stratton Crankshaft and Connecting Rod Shop with confidence on eBay!.
|Published (Last):||5 January 2014|
|PDF File Size:||15.66 Mb|
|ePub File Size:||13.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
Find Your Operator’s Manual | Briggs & Stratton
Can’t locate your model number? The “F02” fault code displays when the drain time exceeds 8 minutes. This can happen if the drain pump filter is restricted or if there is too many suds due to the wrong type of detergent being uses or too much detergent being used. I added an image below showing how to access the drain pump filter. Be sure to have all the water briggw from the tub before removing the drain pump filter.
You will also need to disconnect the power cord from the power source before removing the front lower access panel.
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Thank you for your question. I am sorry you are having a problem with the washer.
The F2 error code is a drain problem. First, I recommend cleaning the debris filter in the drain pump. I have provided you with an image below showing how to access the drain pomp and the filter.
I recommend placing a few old towels down to soak up the water that will come out of the pump when the filter is removed. Once the filter is cleaned reassemble the washer and check the operation. If you still have problems and are using HE detergent please continue on to the following instructions.
If the drain pump runs or hums, you know it is getting voltage. If the pump just hums, there is something jammed in the pump. You can unplug the washer and remove the pump. The motor can be removed from the filter housing to clean out debris. The motor is mounted with 3 or four screws. I have often done this instead of replacing the pump. Check the vanes of the impeller.
If they are broke, you have to replace the pump. The pump comes complete with the filter housing. If the vanes of the impeller are ok just make sure the seal is in position before you secure the motor to the housing. Then retest the washer if the washer drains you have saved yourself the cost of the strayton and labor. If the drain motor runs but does not pump the water out I would suspect the vanes of the impeller are broken or the hoses are plugged. If the vac drains most of the water, you know the hoses are clear and you have to replace the pump.
If the drain motor does not run, you have to check for voltage at the drain motor. Only check the voltage to the drain motor if you know how to safely do so. Put the washer into a drain, spin cycle, and carefully check for volts rbiggs at the drain motor.
If you have vac you need to replace the pump. If you do not have vac to the pump, the problem is in the wiring or the machine control board. If the washer is draining all the water and giving the F2 error code, I suspect the pressure briggw has failed. The contacts in the switch can stick together and cause the same problem. To check the pressure switch first unplug the washer and remove the top of the washer.
Locate the pressure switch and check the wire connector. It should be firmly seated on the pressure switch. Then carefully plug the washer in and start a drain and spin.
Once all of the water is drained, the basket should start to spin. If the basket does not spin, tap the presser switch with the handle of a screw driver. This may break the contacts loose in the pressure switch and start to spin.
If the basket spins, you need to replace the pressure switch. If you have any problems, please let me know by replying below with the model number and more details. Here is a link to order any parts you need.
The sttratton very well could be the bake igniter. The bake igniter brigys glow red and it must pull enough current to cause the oven gas valve to open. If the bake igniter is glowing, I suspect the igniter is too weak to pull enough current to cause the gas valve to open.
Replace the bake igniter and the oven should ignite. If the bake igniter is not glowing, it could have a broken igniter, a faulty electronic oven control or possible a faulty oven safety valve. The igniter can be disconnected and tested for continuity with an Ohm meter. Disconnect the power cord from the power source before servicing the range. All parts are manufacturer-approved, to ensure proper fit and to keep appliances running for years to come.
Purchase requirement calculated before taxes and shipping charges and after other discounts have been applied and must be made in a single transaction. Cannot be applied to previous purchases and cannot be redeemed for cash. Offer valid for online purchases only. In an event of a return, coupon savings may be deducted from your refund. Discount will be automatically applied during check-out. All of our chat agents are currently assisting other customers. Please brigs back in a few minutes.
Get rewarded for shopping. And the more you shop, the faster the benefits add up. It’s super easy to use and best of all – free. You may return an unused and uninstalled part in its original packaging. We must receive the returned part s with the Return Authorization number within days of your original order date. Exclusions apply to products with limited shelf life, which includes but are not limited to batteries, smoke detectors, or chemical based products; these products must be returned within 90 days of the original order date.
Items received damaged must be reported within 10 days of receipt. Credit will be issued for the part s plus tax, minus any shipping charges. Points valid for 14 days. Members earn points on qualifying purchases, excluding sales taxes and strattln fees. Don’t have a profile? It’s fast and easy to create one. Sign up now and you can access your models anytime, anywhere. This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future.
Sign In Register here You can find parts to your models faster by adding models you own to this list.
Briggs & Stratton 98902 098902 Crankshaft and Connecting Rod 793062 699655
Choose your product type. Common model number plates. View sample model numbers by selecting your stratyon brand. Engine 71, Question and Answers Q:.
Find Your Operator’s Manual
Thank you for your question and I understand your concern. Thank you for using Manage my life. Click to Chat We’re available to chat.
Enter your zip code. Automatic Reorder Details Receive free shipping on all automatic reorders with subscription Note: This offer is only valid in rbiggs contiguous U. Chat is currently unavailable We’re sorry! Okay Or call now for immediate assistance: Continue shopping View Cart and Checkout.
Join today and receive: Get all the details Close. Member Exclusive Not a member? Tell us how to save your model. Sign in and keep model in your profile permanently Don’t have a profile? Keep model on this computer temporarily This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future.
Clearing your browser history may delete your saved models.