DIN EN 10216-2 PDF

Buy DIN EN SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES – TECHNICAL DELIVERY CONDITIONS – PART 2. DIN EN Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 2: Non-alloy and alloy steel tubes with specified elevated. ​Manufacturing program with average wall thickness (EN ). Vallourec supplies seamless steel tubes for pressure purposes in accordance with.

Author: Dalkree Sagar
Country: Germany
Language: English (Spanish)
Genre: Science
Published (Last): 20 September 2013
Pages: 42
PDF File Size: 10.59 Mb
ePub File Size: 17.26 Mb
ISBN: 854-7-83936-365-6
Downloads: 63501
Price: Free* [*Free Regsitration Required]
Uploader: Milkis

If the document is revised or amended, you will be notified by email.

All dressed areas shall blend smoothly into the contour of the tube. Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 4: The pipes are manufactured with the diameters between 21,3 — mm and with the wall thickness of up to mm in the case of hot rolling, and with the diameters between 10,2 — and with the wall thickness of up to 12,5 mm in the case of cold drawing.

Tubular Products (EN 10216-2)

Carbon and low-alloy steels ISO The test method is specified by the purchaser. The decision shall be at the discretion of the manufacturer, but shall be stated to the customer at the time of ordering. Page 23 EN B is specified, the material manufacturer shall state in the confirmation of the order whether he is operating according to a quality assurance system certified by a competent body established within the Community and having undergone a specific assessment for materials.

Method of testing at elevated temperature. The tubes shall be delivered with bevelled ends see figure 1. C inspection certificate in accordance with EN The wall thickness shall be measured away from the tube ends in accordance withan agreed procedure.

  HOAGY CARMICHAEL STARDUST PDF

Selection of leak tightness test method see 8. It is recommended that the level 3 personnel be certified in accordance with EN or, at least, an equivalent to it.

This standard is not included in any packages. ENMetallic materials – Charpy impact test – Part 1: ENMetallic materials – Tubes – Drift expanding test.

A B commercial transactions and parties involved; description of products to which the inspection document applies; direction ddin the test pieces and testing temperature; tensile test; impact test if applicable; other tests e. The number of tubes per test unit shall conform to table Please first verify your email before subscribing to alerts.

The tubes of test category 2 shall subjected to a non-destructive testing for the detection of transverse imperfections in accordance with Test pressure for hydrostatic leak tightness test see Non-destructive testing for test category 2 tubes for detection of laminar imperfections see 8.

Non-alloy steel tubes with specified room temperature properties Specifies the technical delivery conditions for two qualities, T1 and T2, of seamless tubes of circular cross section, with specified room temperature properties, made of non-alloy quality steel….

Tubular Products (EN )

Unless option 1 is specified, the tubes may be either hot or cold finished at the discretion of the manufacturer. Welded steel tubes for pressure purposes — Technical delivery conditions — Part 2: Product analysis for the tubes shall be supplied. The test pressure shall be held for not less than 5 s for tubes with an outside diameter D less than or equal to mm and for not less than 10 s for tubes with an outside diameter greater than mm.

Deviations from straightness over any one metre length shall not exceed 3 mm. It is important that the purchaser, at the time of enquiry and order, takes in account the requirements of the relevant national legal regulations for the intended application.

  A COURSE OF MATHEMATICAL ANALYSIS BY SHANTI NARAYAN PDF

Din En 2 Steel Pipe, Din En 2 Steel Pipe Suppliers and Manufacturers at

The tube section shall be flattened in a press until 1021-62 H between platens reaches the value given by the following equation: A test pressure different from that specified in Unless option 7 is specified, the ej of the test method is at the discretion of the manufacturer. List of standards Mass calculator Fundusze europejskie. The tubes shall be cold finished before heat treatment.

EN and prEN In the case of inspection report 3.

Your Alert Profile lists the documents that will be monitored. Non-alloy and alloy steel tubes with specified elevated temperature properties includes Amendment A1: Proceed to Checkout Continue Shopping.

Page 28 EN This standard is also available to be included in Standards Subscriptions. Mechanical properties of seamless steel pipes for elevated temperatures tested in room temperature. ENNon-destructive testing of steel tubes – Part 1: Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 3: The marking shall include the following information: Automatic full peripheral ultrasonic testing of seamless and welded except submerged arc welded steel tubes for the detection of longitudinal imperfections.

Table 3 specifies the permissible deviations of the product analysis from the specified limits 1216-2 cast analysis given in table 2. Subscription pricing is determined by: ENDefinitions and classification of grades of steel. Page 30 EN Impact testing see table 4. Alloy steel tubes shall be inspected and tested in accordance with test category 2 see table