HAAS SL10 PDF

Find great deals for Haas Sl CNC Lathe. Shop with confidence on eBay!. Large selection of second-hand Haas SL available here. Great offers from top traders & auctions all in one place. Buy your Haas SL today!. Productivity Inc – Haas CNC Lathe Operator Manual. Page 1. Haas Lathe Operator Training Manual. Table of Haas VMC (SL) showing the X and Z axis.

Author: Mezisho Sarr
Country: Monaco
Language: English (Spanish)
Genre: Video
Published (Last): 7 December 2018
Pages: 178
PDF File Size: 13.32 Mb
ePub File Size: 2.6 Mb
ISBN: 912-1-90326-749-4
Downloads: 85412
Price: Free* [*Free Regsitration Required]
Uploader: Dukree

The sl10 HAAS has one headstock, and the spindle dl10 is Align the coolant nozzle with the coolant port, as shown. You have successfully subscribed. Remove lock out sl0, power up and zero return the machine. With the turret clamped test the air cylinder for faulty piston seal.

For SL and HL machines, remove the covers as follows: Manually turn the coupling to the left and to the right to feel the distance of the free movement.

Haas Sl CNC Lathe | eBay

Check the incoming air supply. Make corrections as needed.

Make sure a minimum 1″ 25 mm space is between the turret and all objects in the direction of the Z Axis. Air Cylinder Assembly To confirm your subscription, click the link, we’ve sent you by mail. Haaas the turret is removed the springs can be replaced. Remove the rear cover [1]. Standard toolholder kit included with BOT or Hybrid turret.

  IP 24135A PDF

The Haas Resource Center

Mercuriusstraat 28 B Zaventem, Belgium Phone: TC Cluster Gear Use the screwdriver or your thumb to turn the coupling to get access to the coupling screw [1].

Turret Home Switch Belleville Washers 2 TC Cam Lever 8. The lathe has a 12 tool station turret with an X standard axis.

Servo Motor Back to Top. Use a magnet and pass it over the sensors. If the o-ring under the rear turret chip skirt fails it can cause uaas and prevent the turret from rotating into position. A failed o-ring will also allow for coolant and chip intrusion into the back side of the turret.

Haas SL-10

View Privacy and Cookie Policy. Using M43, Unclamp the turret. Go to Video Gallery. Do Not unplug the cable.

Motor Coupling – Alignment – SL/20/30 – ST/10Y

Please click the link in the email we just sent you, to complete the subscription process. The HAAS turning diameter is millimetres. Info-mailer for “Haas SL” By entering and confirming your email address, you will receive an e-mail notification as soon as new offers are received for your search.

  74F32 DATASHEET PDF

Most big websites do this too. Shows are listed by date unless otherwise requested. Swing over crosss slide: Set the meter to AC voltage.

TC Spur Gear keyed Bar Feeders Bar Feeders. In MDI command an M43 and press cycle start to unclamp the turret.

Remove the 3 screws [2], as shown. Die Spring Retainer 9.

Check the turret clamp sensor. A cookie is a small text file that a website hzas on your computer or mobile device when you visit the site. If the magnet did not activate the sensors inspect the cables. TC Turret Cams 2 4. CNC Lathe; 14″ x 16″ x mm max capacity, 1.

Turret Indexer Assembly 2. Swing Diameter Sl0 Front Apron TC Switch Ring Turret Switch Bracket Turn the coupling to the approximate middle of the free movement. If air is escaping from the upper hose unclamp connection on the cylinder the cylinder piston seal is bad and piston should be replaced.