The pasteurisation unit (HTST pasteuriser) is designed for the thermal treatment of milk and dairy products as well as other food products as soft drinks and. For more than 30 years REDA S.p.A. has been acting in the milk pasteurization process, using and constantly developing the plants of the series HTST (High. This innovation in HTST pasteurization is poised to transform the capabilities of dairy processors, allowing them to offer pasteurized milk that is farm-fresh and.
|Country:||Trinidad & Tobago|
|Published (Last):||20 January 2014|
|PDF File Size:||6.85 Mb|
|ePub File Size:||15.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
Parts in contact with the product: Free circulation from outlet to inlet is required and the speed of the homogenizer must be greater than the rate of flow of the timing pump. Turn off the air supply and the main electric switch at the panel. Since the magnetic flow meter continuously senses flow rate, it will signal the electronic controller if the actual flow exceeds the set flow rate for any reason.
The probe should sit as close as possible to STLR probe and be located not greater than 18 inches upstream of the flow diversion device. It, therefore, helps to maintain a higher pressure on the pasteurized side of the heat exchanger. This step requires power.
HTST milk pasteurizer, Flow pasteurizer
These systems are used for time and temperature control of HTST systems. In operation, the electrical signal is sent by the magnetic flow meter to the flow controller, which determines what the actual flow is compared to the flow rate set by the operator. Pasheurizer are currently using guest access Log in. It governs the rate of pazteurizer through the holding tube. Stop the milk and hot water pumps. Ensure availability of sufficient water in the storage tank approximately, equal to the capacity of the plant.
The panel includes a temperature regulator. The balance tank provides a means for recirculation of diverted or pasteurized milk. This gives rise to a need for specific regulations or computer controlled CCP’s of public health significance:.
The pasteurizer should be inspected every day for any leakage and for ensuring cleanliness. The process destroys pathogenic microorganisms by heating the product to hhst moderately high temperature for a brief period. The timing pump draws product through the raw regenerator and pushes milk under pressure through pasteurized regenerator. All water remaining in the plant must be drained. pasteugizer
The package constitutes a tested filter system and a circulation cleaning system. Energy recovery is approx.
AISI Other components and control panel: The milk and the heating circuit are equipped with stainless steel pumps. A significant difference from the normal HTST system with timing pump comes into focus at this point. It also must be interwired so it only operates when FDD is fully forward or fully diverted, and must be “fail-safe”.
The STLR records the temperature of the milk and the time of day. Tube section for sec pasteurization temperature holding time, at min. There are two types of FDD:. Plate pasteurizer with cooling of the heated milk by water in counter flow principle ice water after cooling required. Ice-water connection if required: An integrated after cooling with ice water is optionally available. The indicating thermometer is pasfeurizer the most accurate temperature measurement.
It monitors, controls and records the position of the flow diversion device FDD and supplies power to the FDD during forward flow. Plate pasteurizer with cooling of the heated milk by cold milk in counter flow principle energy saving option. Remove undesirable pasteutizer and flavours 4.
HTST milk pasteurizer (Flow pasteurizer)
Request information Pasteuriser Request information. Open the air vents. Its efficiency may be calculated as follows: The overflow level must always paseturizer below the level of lowest milk passage in regenerator. Application of the magnetic flow meter in the dairy industry has centered around its replacing the positive displacement timing pump as the metering device in HTST pasteurizing systems, where with certain products the timing pump rotors reportedly wear out in a relatively short period of time.
Turn off the chilled water in the cooling sections.
Close the air vents when the milk comes out from them. Another magnetic flow meter based system with an AC variable frequency motor control drive on a centrifugal pump is also possible in lieu of a positive displacement metering pump on a HTST pasteurizer.
To kill bacteria including pathogens. As the last milk leaves the balance tank, tip in the water from the tank.